This is a translucent grey coating, not a solid color. Once cured, the concrete texture beneath remains faintly visible through the finish rather than fully covered. If solid, uniform color is your goal, three coats or the addition of a color pigment paste may be needed to achieve full opacity.
Where this product performs best is as a base layer for flake systems. Broadcast your acrylic flakes directly into the wet epoxy immediately after application, then seal with a clear floor epoxy. The flakes handle the coverage, texture, and finished look — the grey base handles the bond.
Shore D 82 Hardness Water Absorption <0.1% 70°C Heat Deflection 72hr Full Cure 3 Gallon Kit
Why Grey — Not Clear, Not Paint
Engineered for garage floors, workshops, and commercial spaces, Bond Craftor Grey Floor Epoxy delivers a seamless, high-gloss finish that bonds directly to bare concrete. The two-part 2A:1B system self-levels on application, leaving a smooth, professional surface that resists hot tires, chemical spills, and heavy foot traffic for years.
Key Features
Hot tire resistant
70°C heat deflection — handles vehicles without softening or lift
Waterproof & stain-resistant
Under 0.1% water absorption once fully cured
Self-leveling formula
Low viscosity, self-defoaming — no brush marks, no pinholes
Flake compatible
Broadcast color chips over wet epoxy for texture and slip resistance
Technical Specifications
| Mixing ratio | 2A : 1B by volume |
| Part A viscosity (25°C) | 2200 ± 300 mPa·s |
| Part B viscosity (25°C) | 150 mPa·s |
| Mixed viscosity (25°C) | 400 ± 200 mPa·s |
| Pot life (100g at 25°C) | 25 ± 5 minutes |
| Coverage per coat | 280–350 g/m² |
| Hardness after cure | Shore D 82 ± 3 |
| Heat deflection temperature | 70°C |
| Water absorption | < 0.1% |
| Part A density | 1.06 ± 0.05 g/cm³ |
| Part B density | 0.95 ± 0.03 g/cm³ |
| Working temperature | 20–25°C (preheat Part A to 30°C if below 15°C) |
| Humidity limit | Below 85% RH |
| Full cure | 48–72 hours at room temperature |
| Shelf life | 6 months (sealed, original packaging) |
How Much do You Need?
Per gallon per coat
175–200 sq ft
260 ~ 500 sq ft car garage
1 Kit
600 ~ 1000 sq ft car garage
2 Kits
1100 ~ 1600 sq ft car garage
3 Kits
Coverage is estimated for one standard roller-applied coat on properly prepared concrete. Actual coverage may vary depending on concrete porosity, surface condition, application thickness, and project type.
Before You Apply — Surface Prep is Everything
Epoxy doesn't fix dirty concrete — it locks it in. The slab must be:
- Free of oil, grease, dust, and any peeling existing coatings
- Opened via acid etching or mechanical diamond grinding — this creates the pore structure epoxy bonds to
- Completely dry — if water beads on the surface, prep is not complete
- Crack-filled — patch any cracks wider than a hairline before coating
How To Coat Garage Floor Epoxy
With clear instructions and a user-friendly formula, you can achieve professional results with your epoxy floor coating — no experience needed.
Grind & Prepare the Concrete
Remove surface grease and other impurities, repair cracks — the key first step for any epoxy coating for concrete floors.
Apply Epoxy Base Coat
Roll on the mixed epoxy evenly across the floor. The coating begins to self-level, creating a smooth and seamless base layer.
Broadcast Flakes for Texture
Before the epoxy cures, evenly epoxy floor flakes over the surface.Once cured,sweep away any excess flakes.
Seal with Clear Topcoat
Finish with a protective layer using a clear epoxy floor coating to lock in durability and enhance the final gloss.
